玻璃真空熱合夾膠機簡介

工作原理：

玻璃真空熱合夾膠機采用真空袋的原理，對玻璃進行抽真空，在加熱的條件下，將EVA膠片融化，使玻璃及中間材料貼合在一起，從而生產出夾層，夾絲，夾膜或夾膠玻璃。

夾膠機可將絲布，紙制品，字畫和紫外線單向透視膜，調光膜等功能膜或特定的膠片，與普通玻璃通過真空熱合，生產出多種功能的工藝夾層玻璃和裝飾玻璃，也可用于玻璃與PC板，玻璃生產不需要附帶，高壓釜和層壓機。

玻璃真空熱合夾膠機結構簡單可靠，能耗低，質量好，占地面積少，投資少，生產成本低，適用范圍廣，產量高，適合工業化生產要求。

The working principle of glass vacuum heating & laminating machine

By adopting vacuum bag principle,it can joint glass with EVA films through heating and vacuum glass to make laminated glass.

It laminates two pieces of glass into one whole art glass through heating laminated materials and glass for peptezing under vacuum conditions.This machine normal float glass with silk,cotton,paper products,drawings,PET films or special plastecal films to make various art glass and decorative glass.It can also be used to laminate glass with PC sheet,soft sheet and simple and reliable in structure,low consumpteve in energy,good in quantity.which is widely used in glass processing to meet industrialization requirements of modern enterprises.

主要技術參數

 玻璃真空熱合夾膠機功能、特點：

1. 烘箱以風道式運送熱風，此設計能使機箱內部溫度均勻的進行加熱工作。箱內熱量均衡、熱損耗小，采用優質巖棉和硅酸鋁棉材料做成的箱壁，具有良好的保溫效果。

2. 真空床用優質的原生硅膠板拼合而成，經久耐用。

3. 控制箱設計合理、簡捷，預設程序一步走完，操作十分簡便。

4. 本機既可生產夾膠、夾絲玻璃，還可以當烤箱生產聚晶烤漆。

5. 有效空間使用，在真空床范圍內可任意拼放玻璃，不受玻璃形狀和厚度的限制。

6. 高效省電，2-3小時可生產一爐5層硅膠床“合片玻璃”，耗電約35-40度。

The function and characteristics of glass vacuum heating & laminating machine

1. The machine inside use circulation air to keep the temperature balance and low consumption.Its wall is make good quality stainless panel inside use special cotton to keep high temperature.

2. Vacuum beds jointed with good quality and anti-scratch silicone sheet.

3. Its electric cabinet is reasonable in designated easy way to operate by presenting in one step.

4. It can used to make laminated glass and polymer paint baked.

5. Space-saving,galss can be put on vacuum bed freely and is not subject to its shape and thickness.

6. Efficient energy saving,2-3hours to produce a 5 layer of silica gel bed“glass”,the power consumption is about 35-40degrees.

 操作注意事項：

1. 電機必須正傳，如果反轉，必須重新接線。

2. 電控箱必須由專業操作人員操作，檢查電箱時，必須保證電源完全斷開。

3. 爐內溫度高于常溫時，操作人員切勿走進箱內。

4. 硅膠條、硅膠板刮抗拉力只達到普通橡膠的1/5，故一定要小心與玻璃接觸，以免劃破。發現有破損，用高品質的玻璃膠補漏，溫度較高時硅膠板容易破損，請勿翻動。

5. 真空泵要勤換機油，操作環境濕度較大時，機油會吸附水分，導致機油發白，真空度明顯下降，甚至于水分的增加，使機油溢出來。機油在經過一段時間的靜置后，水、油分層，水分棄置，上層的機油可適當使用。

6. 真空泵放置的位置要通風，已方便散熱。

Operation Cautions

1. the motor turns counterclockwise,cables shall be connected again.

2. Electric cabinet shall be operated by professional technician.When it is examined,power shall be switched off completely.

3. Don’t walk into the amchin when its temperature is higher than moderate temperature.

4. Anti-scratching Tate is only 20％ when the silicone bag in high temperature,so please be careful not be scratched by sharp glass.If damaged easily.

5. Vacuum pump Oil shall be changed regularly.Under working environment,vacuum pump to make low pump suction capacity or oil overflow from pump,clean the vacuum pump when you didn’tuse the pump after two weeks.change oil, let the pump working to make sure pump is ok.

6. Vacuum pump shall be put in a dry and ventilating place for convenience of releasing heat.

玻璃真空熱合夾膠機用途：

夾膠機可生產以下產品：